AnyDATA ADU-E100H

Jindra Fucik fulda at seznam.cz
Sat Apr 1 20:08:52 CEST 2006


Takze pro poteseni vsech - potvrdil jsem si co jsem zaslechl - opravdu se 
jedna o ubsa zarizeni, takze mam prvni relevantni odpoved od modemu.

Jdu bojovat s pripojenim k internetu.

pro nedockavce: http://logout.sh.cvut.cz/~fulda/anydata.siemens.patch.gz

<offtopic>
- v cene je obsazen patch na siemens es75, samostatnou verzi neprodavme
- mozna se zmeni jmeno serveru, viz: 
http://www.student.cvut.cz/view.php?cisloclanku=2006040101
</offtopic>


----- Original Message ----- 
From: "Jindra Fucik" <fulda at seznam.cz>
To: "FreeBSD mailing list" <users-l at freebsd.cz>
Sent: Thursday, March 30, 2006 11:43 AM
Subject: Re: AnyDATA ADU-E100H


Tad jsem se koukal na jeden clanek od vodafone, kde popisujou ze qualcomm
cipy se pouzivaji jako ubsa.

Nezkousel nekdo pridat ten modem do seznamu v souboru: /sys/dev/usb/ubsa.c
(nekde kolem radky 224 ;o))
potom pochopitelne jatro s modulama ubsa a ucom.

ja to teda testnu az o vikendu, mozna je to spatnej smer, ale chtel jsem se
podelit o informaci, aby nezapadla.

Jindra

----- Original Message ----- 
From: "Jan Dusátko" <dusatko at e-apollo.cz>
To: "'FreeBSD mailing list'" <users-l at freebsd.cz>
Sent: Friday, March 10, 2006 7:56 PM
Subject: RE: AnyDATA ADU-E100H


> Vitej do klubu ;o)) Tohle uz se snazim vyresit nekolik tydnu a zatim se mi
> vubec nedari ;o)))
>
> -----Original Message-----
> From: users-l-bounces at freebsd.cz [mailto:users-l-bounces at freebsd.cz] On
> Behalf Of Ondra Holecek
> Sent: Friday, March 10, 2006 5:27 PM
> To: users-l at freebsd.cz
> Subject: AnyDATA ADU-E100H
>
>
> ahoj,
>
> potebuju na FreeBSD nastavit tenhle cdma modem, delam to uplne stejne
> jako v tomhle prispevku kdyz se nastavoval ten pvni cdma euroteli modem:
> http://www.freebsd.cz/listserv/archive/users-l/2004-August/010714.html
>
> jenom jsem do /usr/src/sys/dev/usb/usbdevs pridal tohle
>
> vendor ANYDATA    0x16d5   AnyDATA Corporation
> /* AnyDATA CDMA products */
> product ANYDATA ADU_E100H   0x6501  ADU-E100H
>
> a do usb_quirks.c tohle (to s +)
>
>  { USB_VENDOR_YAMAHA, USB_PRODUCT_YAMAHA_RTW65I,
>    ANY, { UQ_ASSUME_CM_OVER_DATA }},
>
> + { USB_VENDOR_ANYDATA, USB_PRODUCT_ANYDATA_ADU_E100H,
> +   ANY, { UQ_ASSUME_CM_OVER_DATA }},
>
>  { USB_VENDOR_QUALCOMM, USB_PRODUCT_QUALCOMM_CDMA_MSM,
>    ANY, { UQ_ASSUME_CM_OVER_DATA }},
>  { USB_VENDOR_QUALCOMM2, USB_PRODUCT_QUALCOMM2_CDMA_MSM,
>    ANY, { UQ_ASSUME_CM_OVER_DATA }},
>  { USB_VENDOR_SUNTAC, USB_PRODUCT_SUNTAC_AS64LX,
>    0x100, { UQ_ASSUME_CM_OVER_DATA }},
>  { 0, 0, 0, { 0 } }
>
> v puvodnim prispevku, autor jeste vola:
>
> cd /usr/src/sys/dev/usb && make -f Makefile.usbdevs
>
> co v u me v 6.0-RELEASE neni (ono to ostatne neni ani v 5.4-RELEASE jak
> jsem tak koukal), ale pan Google tvrdi ze si to udelaj skripty pri
> kompilaci sami, ale nejak se mi to nezda. :(
>
> kazdopadne, porad ten modem po pripojeni vidim jen jako ugen
> ugen0: AnyDATA Corporation AnyDATA CDMA Products, rev 1.10/0.00, addr 2
>
>
> kdyby to pomohlo, tak tohle je vypis pri sysctl hw.usb.debug=1
>
> usbd_new_device bus=0xc1979000 port=2 depth=1 speed=2
> usbd_new_device: adding unit addr=2, rev=110, class=0, subclass=0,
> protocol=0, maxpacket=64, len=18, speed=2
> usbd_find_quirk 0x16d5/0x6501/0: 4096
> usbd_new_device: new dev (addr 2), dev=0xc2244900, parent=0xc198bd80
> usbd_probe_and_attach: trying device specific drivers
> usbd_probe_and_attach: no device specific driver found
> usbd_probe_and_attach: looping over 1 configurations
> usbd_set_config_index: (addr 1) cno=2 attr=0xa0, selfpowered=0, power=500
> usbd_set_config_index: set config 1
> usbd_probe_and_attach: no interface drivers found
> ugen0: AnyDATA Corporation AnyDATA CDMA Products, rev 1.10/0.00, addr 2
> usbd_set_config_index: free old config
> usbd_set_config_index: (addr 1) cno=2 attr=0xa0, selfpowered=0, power=500
> usbd_set_config_index: set config 1
>
>
> dal uz opravdu nevim jak to resit, imho by to takhle melo vytvorit ucom
> a popripade treba nefungovat, nebo dat alespon neco vedet :(
>
>
> tohle jsou relevantni radky z myho kernel konfu:
>
> device   ucom
> device   umodem
> device   uftdi
> options  USB_DEBUG
>
> device      uhci     # UHCI PCI->USB interface
> device      ohci     # OHCI PCI->USB interface
> device      ehci     # EHCI PCI->USB interface (USB 2.0)
> device      usb      # USB Bus (required)
> #device     udbp     # USB Double Bulk Pipe devices
> device      ugen     # Generic
> device      uhid     # "Human Interface Devices"
> device      ukbd     # Keyboard
> device      ulpt     # Printer
> device      umass    # Disks/Mass storage - Requires scbus and da
> device      ums      # Mouse
> device      ural     # Ralink Technology RT2500USB wireless NICs
> device      urio     # Diamond Rio 500 MP3 player
> device      uscanner # Scanners
>
>
> Ondra
> -- 
> FreeBSD mailing list (users-l at freebsd.cz)
> http://www.freebsd.cz/listserv/listinfo/users-l
>
>
> -- 
> FreeBSD mailing list (users-l at freebsd.cz)
> http://www.freebsd.cz/listserv/listinfo/users-l

-- 
FreeBSD mailing list (users-l at freebsd.cz)
http://www.freebsd.cz/listserv/listinfo/users-l 




More information about the Users-l mailing list