Kompilace kernelu

Petr Var PVar at seznam.cz
Mon Oct 27 10:16:32 CET 2003


No toto
   device scbus
   device da
   device pass
 jsou zapoznámkovaný. 

Verze BSD je 4.7 RELEASE.

Zde je konfigurák kernelu


machine         i386
cpu             I686_CPU

ident           TESTKERN

maxusers        100

symbols

options         INET                    #InterNETworking
options         INET6                   #IPv6 communications protocols
options  FFS            #Berkeley Fast Filesystem
options  FFS_ROOT       #FFS usable as root device [keep this!]
options  SOFTUPDATES      #Enable FFS soft updates support
options  UFS_DIRHASH      #Improve performance on big directories
options  MFS            #Memory Filesystem
options  MD_ROOT          #MD is a potential root device
options  NFS            #Network Filesystem
options  NFS_ROOT       #NFS usable as root device, NFS required
options  CD9660         #ISO 9660 Filesystem
options  CD9660_ROOT      #CD-ROM usable as root, CD9660 required
options  PROCFS         #Process filesystem
options  COMPAT_43        #Compatible with BSD 4.3 [KEEP THIS!]
options  UCONSOLE       #Allow users to grab the console
options  USERCONFIG       #boot -c editor
options  VISUAL_USERCONFIG #visual boot -c editor
options  KTRACE         #ktrace(1) support
options  SYSVSHM          #SYSV-style shared memory
options  SYSVMSG          #SYSV-style message queues
options  SYSVSEM          #SYSV-style semaphores
options  P1003_1B       #Posix P1003_1B real-time extensions
options  _KPOSIX_PRIORITY_SCHEDULING
options  ICMP_BANDLIM     #Rate limit bad replies
options  KBD_INSTALL_CDEV # install a CDEV entry in /dev
options  AHC_REG_PRETTY_PRINT  # Print register bitfields in debug
         # output.  Adds ~128k to driver.
options  AHD_REG_PRETTY_PRINT  # Print register bitfields in debug
         # output.  Adds ~215k to driver.

#Toto jsem dopsal z duvodu NATu abych ho mohl pouzit
options         IPFIREWALL
options         IPDIVERT
options         IPFIREWALL_DEFAULT_TO_ACCEPT
options         IPFIREWALL_VERBOSE
options         DUMMYNET

device   isa
device   eisa
device   pci

# Floppy drives
device   fdc0   at isa? port IO_FD1 irq 6 drq 2
device   fd0    at fdc0 drive 0
device   fd1    at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device  fdc0

# ATA and ATAPI devices
device   ata0   at isa? port IO_WD1 irq 14
device   ata1   at isa? port IO_WD2 irq 15
device   ata
device   atadisk          # ATA disk drives
device   atapicd          # ATAPI CDROM drives
device   atapifd          # ATAPI floppy drives
device   atapist          # ATAPI tape drives
options  ATA_STATIC_ID    #Static device numbering


# atkbdc0 controls both the keyboard and the PS/2 mouse
device   atkbdc0  at isa? port IO_KBD
device   atkbd0 at atkbdc? irq 1 flags 0x1
device   psm0   at atkbdc? irq 12

device   vga0   at isa?

# splash screen/screen saver
pseudo-device   splash

# syscons is the default console driver, resembling an SCO console
device   sc0    at isa? flags 0x100


# Floating point support - do not disable.
device   npx0   at nexus? port IO_NPX irq 13

# Power management support (see LINT for more options)
device   apm0   at nexus? disable flags 0x20 # Advanced Power Management

# PCCARD (PCMCIA) support
device   card
device   pcic0  at isa? irq 0 port 0x3e0 iomem 0xd0000
device   pcic1  at isa? irq 0 port 0x3e2 iomem 0xd4000 disable

# Serial (COM) ports
device   sio0   at isa? port IO_COM1 flags 0x10 irq 4
device   sio1   at isa? port IO_COM2 irq 3
device   sio2   at isa? disable port IO_COM3 irq 5
device   sio3   at isa? disable port IO_COM4 irq 9

# Parallel port
device   ppc0   at isa? irq 7
device   ppbus    # Parallel port bus (required)
device   lpt      # Printer
device   plip     # TCP/IP over parallel
device   ppi      # Parallel port interface device


# PCI Ethernet NICs.
device   de       # DEC/Intel DC21x4x (``Tulip'')
device   em       # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'')
device   txp      # 3Com 3cR990 (``Typhoon'')
device   vx       # 3Com 3c590, 3c595 (``Vortex'')

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device   miibus   # MII bus support
device   dc       # DEC/Intel 21143 and various workalikes
device   fxp      # Intel EtherExpress PRO/100B (82557, 82558)
device   pcn      # AMD Am79C97x PCI 10/100 NICs
device   rl       # RealTek 8129/8139
device   sf       # Adaptec AIC-6915 (``Starfire'')
device   sis      # Silicon Integrated Systems SiS 900/SiS 7016
device   ste      # Sundance ST201 (D-Link DFE-550TX)
device   tl       # Texas Instruments ThunderLAN
device   tx       # SMC EtherPower II (83c170 ``EPIC'')
device   vr       # VIA Rhine, Rhine II
device   wb       # Winbond W89C840F
device   xl       # 3Com 3c90x (``Boomerang'', ``Cyclone'')
device   bge      # Broadcom BCM570x (``Tigon III'')

# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
device   ed0    at isa? port 0x280 irq 10 iomem 0xd8000
device   ex
device   ep
device   fe0    at isa? port 0x300
# Xircom Ethernet
device   xe
# PRISM I IEEE 802.11b wireless NIC.
device   awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
device   wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
device   an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
device   ie0    at isa? port 0x300 irq 10 iomem 0xd0000
#device  le0    at isa? port 0x300 irq 5 iomem 0xd0000
device   lnc0   at isa? port 0x280 irq 10 drq 0
device   cs0    at isa? port 0x300
device   sn0    at isa? port 0x300 irq 10

# Pseudo devices - the number indicates how many units to allocate.
pseudo-device   loop      # Network loopback
pseudo-device   ether     # Ethernet support
pseudo-device   sl      1 # Kernel SLIP
pseudo-device   ppp     1 # Kernel PPP
pseudo-device   tun       # Packet tunnel.
pseudo-device   pty       # Pseudo-ttys (telnet etc)
pseudo-device   md        # Memory "disks"
pseudo-device   gif       # IPv6 and IPv4 tunneling
pseudo-device   faith   1 # IPv6-to-IPv4 relaying (translation)

# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device   bpf       #Berkeley packet filter

# USB support
device   uhci     # UHCI PCI->USB interface
device   ohci     # OHCI PCI->USB interface
device   usb      # USB Bus (required)
device   ugen     # Generic
device   uhid     # "Human Interface Devices"
device   ukbd     # Keyboard
device   ulpt     # Printer
device   umass    # Disks/Mass storage - Requires scbus and da
device   ums      # Mouse
device   uscanner # Scanners
device   urio     # Diamond Rio MP3 Player
# USB Ethernet, requires mii
device   aue      # ADMtek USB ethernet
device   cue      # CATC USB ethernet
device   kue      # Kawasaki LSI USB ethernet





> Posli prosimte konfiguraci KERNELU. umass nema s DUMMYNET nic spolecneho.
> Mas v kernelu take device:
>            device scbus
>            device da
>            device pass
> 
> Ty jsou totiz nutne pro podporu umass. Ale to jen strilim odboku, lepi bude
> ten konfigurak a verze FreeBSD.
> 
> 			Adam
> 
> > 
> > linking kernel
> > umass.o: In function `umass_cam_attach_sim':
> > umass.o(.text+0x137f): undefined reference to `cam_simq_alloc'
> > umass.o(.text+0x13a5): undefined reference to `cam_sim_alloc'
> > umass.o(.text+0x13be): undefined reference to `xpt_bus_register'
> > umass.o(.text+0x13ce): undefined reference to `cam_simq_free'
> > umass.o: In function `umass_cam_rescan_callback':
> > umass.o(.text+0x13e7): undefined reference to `xpt_free_path'
> > umass.o: In function `umass_cam_rescan':
> > umass.o(.text+0x1431): undefined reference to `xpt_periph'
> > umass.o(.text+0x143a): undefined reference to `xpt_create_path'
> > umass.o(.text+0x144d): undefined reference to `xpt_setup_ccb'
> > umass.o(.text+0x1468): undefined reference to `xpt_action'
> > umass.o: In function `umass_cam_detach_sim':
> > umass.o(.text+0x151f): undefined reference to `xpt_bus_deregister'
> > umass.o(.text+0x153d): undefined reference to `cam_sim_free'
> > umass.o: In function `umass_cam_detach':
> > umass.o(.text+0x157e): undefined reference to `xpt_create_path'
> > umass.o(.text+0x159f): undefined reference to `xpt_async'
> > umass.o(.text+0x15a7): undefined reference to `xpt_free_path'
> > umass.o: In function `umass_cam_action':
> > umass.o(.text+0x18c5): undefined reference to `xpt_done'
> > umass.o(.text+0x18d5): undefined reference to `xpt_done'
> > umass.o: In function `umass_cam_cb':
> > umass.o(.text+0x19d1): undefined reference to `xpt_done'
> > umass.o: In function `umass_cam_sense_cb':
> > umass.o(.text+0x1ad8): undefined reference to `xpt_done'
> > umass.o(.text+0x1ae9): undefined reference to `xpt_done'
> > umass.o(.text+0x1b03): more undefined references to `xpt_done' follow
> > *** Error code 1
> > 
> > Stop in /usr/src/sys/compile/TESTKERN.
> > 
> > Nemate nekdo zkusenost o jaky problem se jedna? Diky za radu
> > 
> >  Petr Varga

____________________________________________________________
MMS až na rok zdarma!
Oskarův Dárkový koš nabízí i MMSky. Až rok budete MMSkovat zdarma ? a navíc
pořídite i zvýhodněný mobil. http://ad2.seznam.cz/redir.cgi?instance=62734%26url=http://www.oskarmobil.cz/services/whatsnew.php




More information about the Users-l mailing list