GPRS prakticky

[Zbynek Houska]

Dobry den,

konfiguraci  jsem opsal, avsak pripojen nejsem. Pokud dam ono "set log
local..." a pak dial tak to hned chcipne. Pokud dam dial primo tak je to
"ukecanejsi" viz prilozenej soubor.

Zbynek
-- 
If one is lucky, a solitary fantasy can totally transform one million 
realities. 
-Maya Angelou 
-------------- next part --------------
Script started on Wed Oct  8 17:16:22 2003
root at skippy# ppp ETNonstop
Working in interactive mode
Using interface: tun0
tun0: Command: default: set device /dev/cuaa0
tun0: Command: default: set speed 115200
tun0: Command: default: set dial ABORT BUSY ABORT NO\sCARRIER ABORT NO\sDIALTONE            TIMEOUT 20            "" AT OK-AT-OK            AT+CEER OK-AT+CPIN=27902790-OK-AT-OK            AT+CGDCONT=1,IP,\T OK           \dATDT*99***1# CONNECT
tun0: Command: default: set hangup "" AT+CEER OK
tun0: Command: default: set timeout 60
tun0: Command: default: disable lqr
tun0: Command: default: set server 3000 ********
tun0: Phase: Listening at port 3000.
tun0: Command: ETNonstop: set phone internet
tun0: Command: ETNonstop: set authname USERNAME
tun0: Command: ETNonstop: set authkey ********
tun0: Command: ETNonstop: set ifaddr 0/0 192.168.254.254/0 255.255.255.0 160.218.1.1
tun0: Command: ETNonstop: nat enable yes
tun0: Command: ETNonstop: disable iface-alias
tun0: Command: ETNonstop: enable proxy
tun0: Command: ETNonstop: nat deny_incoming no
tun0: Command: ETNonstop: nat same_ports yes
tun0: Command: ETNonstop: nat use_sockets yes
tun0: Command: ETNonstop: add default HISADDR
tun0: Command: ETNonstop: set filter dial 0 permit 0 0
tun0: Command: ETNonstop: set filter alive 0 permit 0/0 0/0
tun0: Command: ETNonstop: set accmap 0x000a0000
tun0: Command: ETNonstop: disable deflate pred1 vjcomp
tun0: Phase: PPP Started (interactive mode).
ppp ON skippy> set log local Phase Chat LCP IPCP CCP tun
tun0: Command: /dev/tty: set log local Phase Chat LCP IPCP CCP tun
ppp ON skippy> dial
tun0: Phase: bundle: Establish
tun0: Phase: deflink: closed -> opening
tun0: Phase: deflink: Connected!
tun0: Phase: deflink: opening -> dial
tun0: Chat: Phone: internet
tun0: Chat: deflink: Dial attempt 1 of 1
ppp ON skippy> tun0: Chat: Send: AT
tun0: Chat: Expect(20): OK
tun0: Chat: Received: 
tun0: Chat: Received: NO DIALTONE
tun0: Warning: Chat script failed
tun0: Phase: deflink: dial -> hangup
tun0: Phase: deflink: Disconnected!
tun0: Phase: deflink: Connect time: 0 secs: 0 octets in, 0 octets out
tun0: Phase: deflink: 0 packets in, 0 packets out
tun0: Phase:  total 0 bytes/sec, peak 0 bytes/sec on Wed Oct  8 17:16:57 2003
tun0: Phase: deflink: hangup -> closed
tun0: Phase: bundle: Dead
ppp ON skippy> dial
tun0: Phase: bundle: Establish
tun0: Phase: deflink: closed -> opening
tun0: Phase: deflink: Connected!
tun0: Phase: deflink: opening -> dial
tun0: Chat: Phone: internet
tun0: Chat: deflink: Dial attempt 1 of 1
ppp ON skippy> tun0: Chat: Send: AT
tun0: Chat: Expect(20): OK
tun0: Chat: Received: 
tun0: Chat: Received: OK
tun0: Chat: Send: AT+CEER
tun0: Chat: Expect(20): OK
tun0: Chat: Received: 
tun0: Chat: Received: +CEER: 0,0,0
tun0: Chat: Received: 
tun0: Chat: Received: OK
tun0: Chat: Send: AT+CGDCONT=1,IP,internet
tun0: Chat: Expect(20): OK
tun0: Chat: Received: 
tun0: Chat: Received: OK
tun0: Chat: Send: ATDT*99***1#
tun0: Chat: Expect(20): CONNECT
tun0: Chat: Expect timeout
tun0: Warning: Chat script failed
tun0: Phase: deflink: dial -> hangup
tun0: Phase: deflink: Disconnected!
tun0: Phase: deflink: Connect time: 23 secs: 0 octets in, 0 octets out
tun0: Phase: deflink: 0 packets in, 0 packets out
tun0: Phase:  total 0 bytes/sec, peak 0 bytes/sec on Wed Oct  8 17:17:06 2003
tun0: Phase: deflink: hangup -> closed
tun0: Phase: bundle: Dead
ppp ON skippy> exit
tun0: Warning: exit: Invalid command
tun0: Warning: exit: Failed 1
ppp ON skippy> q
root at skippy# exit
exit

Script done on Wed Oct  8 17:17:47 2003