Problem s usbd

Zbynek Houska zhouska at cz.foxconn.com
Wed Jun 25 08:16:41 CEST 2003


Dobry den,

  stala se mi jedna zvalstni vec. Na mem stroji s 4.8 RELEASE mi nejde
pripojit usb zip 100 mb mechanika. Pred casem jsem tam mel jeste 5.0 REL. a
tam bylo vse v poradku.
  Prikladam vypis z dmesg:

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RELEASE #0: Sun Jun 22 00:35:29 CEST 2003
    zhouska at skippy.localdomain:/usr/src/sys/compile/CUSTOM
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel Pentium III (794.66-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x683  Stepping = 3
  
atapci0: <VIA 82C596 ATA66 controller> port 0xfff0-0xffff at device 2.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> irq 10 at device 2.2 on pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6
viapropm0: SMBus I/O base at 0xfe00
viapropm0: <VIA VT82C596A Power Management Unit> port 0xfe00-0xfe0f at
device 2.3 on pci0
viapropm0: SMBus revision code 0x0
smb0: <SMBus general purpose I/O> on smbus0
rl0: <RealTek 8139 10/100BaseTX> port 0x7400-0x74ff mem
0xfcfeff00-0xfcfeffff irq 5 at device 14.0 on pci0
rl0: Ethernet address: 00:30:4f:14:72:1f
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=0x14f1, dev=0x1033) at 15.0 irq 9
pcm0: <ESS Technology Allegro-1> port 0x7800-0x78ff irq 5 at device 18.0 on
pci0
pcm0: <ESS Technology ES1921 ac97 codec>
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
orm0: <Option ROM> at iomem 0xc0000-0xca7ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model NetMouse/NetScroll Optical, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
DUMMYNET initialized (011031)
BRIDGE 020214 loaded
IP packet filtering initialized, divert disabled, rule-based forwarding
enabled, default to accept, unlimited logging
IP Filter: v3.4.31 initialized.  Default = pass all, Logging = enabled
ad0: 19470MB <QUANTUM FIREBALLP LM20> [39560/16/63] at ata0-master UDMA66
acd0: DVD-ROM <Pioneer DVD-ROM ATAPIModel DVD-115 0127> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a

Na konci bootovani mi usbd sdeli, ze nenalezl zadna zarizeni. Troufam si
tvrdit, ze by nemel byt problem v HW, ponovandz jsem tam pro jistotu dal
disk s w2k a mechaniku pripojil bez problemu...Vyse zmineny problem nastane
i v pripade kdy bootuju z GENERIC jadra.
Mohl by mi nekdo poradit?

Zbynek



More information about the Users-l mailing list